 |
 |
| |||||||||||||||||||||||||||||||||||
|
TE Lesson: Work and Power: Waterwheel
Related Curriculum
Learning Objectives (Return to Contents) After this lesson, students should be able to:
Introduction/Motivation (Return to Contents)
To start this lesson, show the class pictures of waterwheels. Explain that in the past, waterwheels were used to grind grain into flour and saw timber. These processes take advantage of the mechanical energy produced by the spinning axle. Modern hydroelectric power plants use the same waterwheel concept to spin turbines in a dam to produce electricity. Figure 1 shows how flowing water in a dam can spin a rotor. You can illustrate the concept of using mechanical energy to produce electricity by using a hand generator to power a light bulb. The turbines in a dam provide energy to a generator in the same way and can provide energy for entire cities. Explain that engineers calculate the power produced by a dam by examining the amount and speed of the flowing water. They can determine how much electricity the turbine can produce and how large an area it can reliably supply with energy. Introduce the activity and explain that the students will do a similar exercise to determine the amount of work a model waterwheel can do and how much power it can generate. Before the activity, present and explain the formulas for work and power that are presented in the Lesson Background section. Lesson Background & Concepts for Teachers (Return to Contents) A brief review of the concepts of potential and kinetic energy (covered in detail in the previous lesson) and work and power, is provided below. Potential energy is the energy that an object has because of its position. Potential energy can also be thought of as stored energy — energy that an object has, as an inherent characteristic, but is not in use. It is sometimes called gravitational potential energy (PE). It can be expressed mathematically as follows: PE = mass x g x height where PE is the potential energy measured in Joules (J) and g is the acceleration due to gravity. At sea level, g = 9.81 meters/sec2. An example of potential energy is a book resting on the edge of a table. If you were to nudge it off the edge of the table, the book would fall to the floor and make a loud noise. This is an expression of kinetic energy. Kinetic energy is the energy an object has because of its motion; any object that is moving has kinetic energy. The falling book in this example is an illustration of kinetic energy. The kinetic energy depends on both mass and velocity and can be expressed mathematically as follows:
Two new concepts that will be discussed in this lesson are work and power. Work is force acting over a distance and can be expressed as: Work = force x distance A Newton (N) is the unit of force in the metric system. To find the weight, or downward force, of an object, simply multiply its mass by gravity. For instance, an object with a mass of 10 kilograms would relate to the following weight: 10 kilograms x 9.81 meters/second2 = 98.1 kilograms*meters/sec2 = 98.1 Newtons. Now, if a force of 10 Newtons was used to move an object 20 meters, we can determine the work involved. You can visualize this as a person pushing against a big box and sliding it across the floor. Work = 10 Newtons x 20 meters = 200 Newton*meters = 200 Joules. A Joule (J) is the unit of work and is the same thing as Newton meter. Power is work done over a period of time and has units of Watts (W), or Joules/sec. An illustration of power is described in the following example. Two piles of bricks need to be moved across a street. Mary carries two bricks at a time and takes two days to complete the job, while Elizabeth, who is driving a backhoe, does the job in 15 minutes. Mary and Elizabeth both do exactly the same amount of work. However, the amount of power expended is much different. If this job requires 20,000 Joules of work, we can calculate the power of the backhoe. First convert 15 minutes into seconds: 15 min x 60 sec/min = 900 sec. Then, divide the number of Joules required by the number of seconds: 20,000 Joules ÷ 900 sec = 22.2 Watts. Elizabeth would then be producing 22.2 Watts of power. On the other hand, Mary would only produce 0.116 Watts of power. Thus, if more power is generated, the quicker the work is performed. The concepts of work and power are very important to engineers. For example, the power rating of an engine describes how fast a car can accelerate. All cars can go 60 mph, but a sports car such as a Corvette, which has twice the power of most cars, will accelerate to 60 mph very quickly. Engineers need to determine how powerful an engine must be so the car drives well on hills and curves, as well as passes other cars quickly on a freeway. However, powerful engines are costly and if the engine is too expensive, not as many people will buy the car. Power is also very important in electricity generation. Water will force turbine blades to move and the power of the water will determine the amount of power generated. Engineers can calculate how much power a hydroelectric plant can generate and therefore how large an area or how large a city it can supply with electricity. Power is also important in simpler systems like the operation of building elevators. The amount of power used will determine how quickly an elevator can rise and the maximum weight the elevator can lift. Vocabulary/Definitions (Return to Contents)
Associated Activities (Return to Contents)
Lesson Closure (Return to Contents)
Briefly review the differences between the concepts of power and work. Reiterate that different amounts of power will do the same amount of work over different periods of time (i.e., less power takes longer). Show a photograph of a famous dam, like the Hoover Dam, and point out how much potential energy exists at the top of the dam. Talk about the work done by the water on the turbines and the power generated to meet the needs of cities like Phoenix and Las Vegas. Explain how engineers of all disciplines are needed to work on projects like dams. Civil engineers design and construct the dam, geotechnical engineers monitor the earth that the dam is built upon, environmental engineers monitor the effects of the dam and mitigate the impact of the dam upon the environment, mechanical engineers construct turbines for the wells, and electrical engineers monitor and construct a power grid to provide energy to surrounding cities. Assessment (Return to Contents) Pre-Lesson Assessment Voting: Ask the students to vote on the following question.
Post-Introduction Assessment Brainstorming: In small groups, have the students engage in open discussion. Remind students that no idea or suggestion is "silly." All ideas should be respectfully heard. Ask the students:
Lesson Summary Assessment Question/Answer: Have students answer the following question in a short paragraph in their journals or on a sheet of paper:
Lesson Extension Activities (Return to Contents) The following website provides a good description of work and power and also includes interactive exercises: http://www.physicsclassroom.com/Class/energy/U5L1e.html Hydroelectric power provides an efficient alternative to traditional electricity sources such as coal and other fossil fuels. Have the students discuss another possible alternative energy source, wind power. Discuss the similarities between wind power and hydroelectric power (i.e., water spins a turbine blade, wind turns a blade on the windmill). Discuss the advantages and disadvantages of these alternative energy sources. Relate that although alternative energy sources are becoming more cost-effective, they are usually more expensive than using fossil fuels. Hydroelectric power, however, is currently cost competitive and cost of wind power is becoming competitive in some regions. An advantage of alternative energy sources is that they are renewable (the sources of fuel do not get used up). Another advantage is that they do not produce pollution like burning fossil fuels do. However, there are some environmental impacts by both wind and water sources. Dams can destroy the ecosystem of a river by changing flows, preventing normal river behavior such as silting and flooding, and preventing fish from getting safely upstream. Wind turbines often spin too fast for birds to see and the birds fly into the turbines and die. Compare the risks of pollution by fossil fuels to the environmental impact of these cleaner fuel sources. The following link provides more detailed information on renewable energy: http://www.nrel.gov/. References (Return to Contents) Kahan, Peter. Science Explorer: Motion, Forces, and Energy, Upper Saddle River, NJ: Prentice Hall, 2000. http://www.angelfire.com/journal/millbuilder/terms.html http://www.energyquest.ca.gov/story/chapter12.html http://www.physicsclassroom.com/Class/energy/energtoc.html Owner (Return to Contents) Integrated Teaching and Learning Program, College of Engineering, University of Colorado at BoulderContributors Bailey Jones, Matt Lundberg, Chris Yakacki, Malinda Schaefer Zarske, Denise CarlsonCopyright © 2004 by Regents of the University of Colorado.The contents of this digital library curriculum were developed under a grant from the Fund for the Improvement of Postsecondary Education (FIPSE), U.S. Department of Education and National Science Foundation GK-12 grant no. 0226322. However, these contents do not necessarily represent the policies of the Department of Education or National Science Foundation, and you should not assume endorsement by the federal government. Last Modified: July 12, 2007 | ||||||||||||||||||||||||||||||||||||
. Have the students read the lessons and work the problems, and check their answers.
